DIY Fireplace Heat Exchanger
Step-by-step guide made from Indy Farm Life's YouTube video.
A custom heat exchanger for a 42-inch fireplace, built from 1.5-inch black steel pipe. This system captures wasted heat and uses an inline fan to blow it back into the room, increasing the fireplace's efficiency and heat output.
The full step-by-step Spetz Specs for this project (every part, size, diagram and step, free): DIY Fireplace Heat Exchanger Spetz Specs.
- Difficulty: intermediate
- Finished size: Fits a 42-inch fireplace; manifold is approx. 24-26 inches wide
Disclaimer
- Fireplaces, heat exchangers, and combustion systems can be dangerous. Do NOT copy this build without understanding local codes, safety requirements, and proper materials. Never use galvanized pipe or toxic materials.
Safety
- Do not use galvanized pipe, as it can release toxic zinc fumes when heated to high temperatures.
- Do not use any pipe dope or thread sealant on the fittings inside the firebox. It will burn off and create unpleasant or potentially harmful fumes.
- This project involves a live fire. Build and operate at your own risk. Always have a fire extinguisher nearby and a carbon monoxide detector in the room.
- The outlet pipe will become extremely hot. Ensure it is positioned where it cannot be accidentally touched, especially by children or pets.
Must know before you build
- Never use galvanized pipe; it releases toxic zinc fumes when heated.
- Avoid pipe dope/sealant on firebox fittings; it burns off, creating fumes.
- Minimize 90-degree elbows; too many restrict airflow, reducing efficiency.
- Use a strong fan; a weak fan won't push enough air for effective heat transfer.
- Elevate pipes above coals with a tall grate to prevent deformation and failure.
- Source intake air from outside to prevent negative room pressure and cold drafts.
Tools
- Inline Fan (4 inch)
- Fan Speed Controller (Rheostat) (optional)
- Pipe Wrenches
- Infrared Thermometer (VEVOR) (optional)
- Leaf Blower (Cordless, DeWalt) (optional)
Materials
- Black Gas Pipe (1.5 inch diameter)
- Black Pipe Fittings (multiple, black gas pipe fittings, 1.5 inch)
- Flexible Ductwork (4 inch diameter)
- Fernco Couplers (2, rubber coupler, Fernco, 4 inch)
- Firewood
- Fireplace Grate (1, Heavy-duty)
Step by step
Step 1: Preparing and Lighting the Fire
The heavy-duty fireplace grate is placed over the heat exchanger pipes, and a fire is started using a gas log lighter and kindling.
- Position the Fireplace Grate. Place the heavy-duty grate into the fireplace, positioning it next to the heat exchanger pipes.
- Tip: Using a tall, heavy-duty grate elevates the fire, which protects the heat exchanger pipes from direct, prolonged contact with the hottest coals and improves their lifespan.
- Light the Fire. Use a gas log lighter or other fire starter to ignite your kindling and establish a fire on the grate.
Step 2: Initial Performance Test
With the fire just getting started, an infrared thermometer is used to measure the baseline temperatures of the pipes and the air coming out of the exchanger.
- Measure Pipe Temperatures. Use an infrared thermometer to measure the surface temperature of various points on the pipe system inside the firebox.
- Measure Air Output Temperature. Turn on the inline fan and use the thermometer to measure the temperature of the air being blown out of the exchanger's outlet pipe.
Step 3: Testing After 30 Minutes
After the fire has been burning for 30-40 minutes and has a good coal bed, the temperatures are measured again, showing a significant increase in heat output.
- Re-Measure Pipe Temperatures. With the fire now much hotter, use the infrared thermometer to re-measure the surface temperatures of the pipes inside the firebox.
- Measure Hot Air Output. Measure the temperature of the air exiting the outlet pipe. In the video, the temperature has increased to over 225°F.
Step 4: Modifying the Output Nozzle
To prevent the hot air from being drawn back into the fire, a 90-degree elbow and a short pipe are attached to the outlet to direct the airflow upwards.
- Attach Elbow and Extension Pipe. Carefully thread a 90-degree elbow followed by a short length of pipe onto the hot air outlet. Use gloves as the pipe is hot.
- Watch out: Make sure you use gloves as the pipe is very hot
Step 5: High-Airflow Test with Leaf Blower
To demonstrate the impact of airflow, a leaf blower is used to force a high volume of air through the system, resulting in a massive increase in heat output.
- Connect the Leaf Blower. With the fire burned down to a hot coal bed, connect a leaf blower to the intake of the heat exchanger system.
- Measure Maximum Temperature Output. Turn on the leaf blower and measure the air temperature at the outlet. In the video, the increased airflow pushes the temperature to over 360°F.