Porcelain Tile Patio with Contrasting Border and Recessed Drain Covers
Step-by-step guide made from Tidybricks patio restore's YouTube video.
Install a multi-size grey porcelain tile patio framed by a 200mm ivory porcelain border over a compacted 100mm MOT Type 1 sub-base. The project covers excavating and setting drainage fall levels, laying primed slabs on a semi-dry sharp sand and cement mortar bed, fitting recessed inspection chamber covers, and filling the joints with flowable exterior grout.
The full step-by-step Spetz Specs for this project (every part, size, diagram and step, free): Porcelain Tile Patio with Contrasting Border and Recessed Drain Covers Spetz Specs.
- Difficulty: advanced
Safety
- Wear a dust mask and eye protection when pouring dry cementitious grout powder and cutting porcelain or cast iron with power saws and grinders.
- Wear waterproof gloves and knee pads when handling and kneeling near wet cement mortar to prevent skin irritation or cement burns.
- Keep 240V extension leads and power tools clear of pooled water when pressure-washing and wet-grouting the patio.
Must know before you build
- Slurry prime every slab underside; unprimed non-porous porcelain will not bond to the mortar bed.
- Compact MOT Type 1 in two 50mm layers instead of one 100mm pass to prevent sub-base settling.
- Use sharp grit sand instead of soft building sand for the semi-dry mortar bedding mix.
- Pre-wet tiles and wash away grout slurry within 20 minutes to prevent permanent surface staining.
- Cut the old cast-iron manhole rim with an angle grinder so the recessed tray sits flush.
Tools
- Mini excavator (tracked micro digger, JCB, 8008 CTS) (optional)
- Tracked power barrow (motorized tracked dumper) (optional)
- Shovel (hand shovel)
- String line and stakes (mason's string line with steel pins)
- Spirit level (long box-section spirit level, Stabila)
- Plate compactor (petrol vibratory plate compactor (wacker plate), Belle)
- Wheelbarrow (builder's wheelbarrow)
- Brick trowel (pointed masonry trowel)
- Rubber mallet (white-headed rubber paving mallet)
- Angle grinder (corded angle grinder with cutting disc, DeWalt)
- Wet tile rail saw (corded wet plunge/rail saw, Flex)
- Paddle mixer (corded twin-paddle electric mixer)
- Flexible mixing tub (heavy-duty flexible plastic tub)
- Pressure washer (electric pressure washer, Nilfisk)
- Rubber floor squeegee (long-handled rubber blade squeegee)
Materials
- Grey porcelain patio tiles (porcelain paving slabs, Marshalls, Symphony Classic Grey, 800mm x 800mm, 800mm x 400mm, 400mm x 400mm)
- Ivory porcelain border tiles (porcelain paving slabs, Marshalls, ivory, 600mm x 600mm (cut to 200mm x 600mm))
- MOT Type 1 hardcore (crushed aggregate sub-base, Type 1 MOT, 100mm total depth (two 50mm layers))
- Sharp sand (sharp grit sand)
- Cement (Portland cement)
- Stone dust (2 tons, fine aggregate blinding)
- Paving primer (slurry bond primer, Marshalls, 20 kg tub)
- Tile spacers (4 per tile, plastic paving spacers)
- Recessed manhole covers (2, recessed square inspection chamber trays, one circular-base square tray and one smaller corner square tray)
- Exterior jointing grout (flowable cementitious paving grout, Marshalls, mixed with 4.25 litres of water per tub)
Step by step
Step 1: Excavate the patio area and set level string lines
Excavate the lawn and soil across the patio footprint, then set taut string lines two bricks below the damp-proof course with a 10mm-per-meter drainage fall away from the house.
- Strip the turf and excavate the patio footprint. Cut along the perimeter of the new patio with a shovel and use a mini excavator and tracked power barrow to strip away the turf and topsoil across the entire patio area.
- Tip: Plan the border layout before excavating so the trench footprint accounts for the 200mm perimeter frame.
- Set perimeter string lines with a 10mm-per-meter drainage fall. Drive steel pins around the excavated perimeter and run taut string lines starting two bricks below the house damp-proof course (DPC). Slope the string lines away from the house at a fall of 10mm per meter (27mm total drop over the 2.7m span).
- Tip: Set the house-side level two bricks below the damp-proof course (DPC) and drop the string line 10mm for every meter across to shed water away from the building.
- Common mistake: Setting the patio level too close to the damp-proof course or without sufficient fall away from the house.
Step 2: Lay and compact the MOT Type 1 hardcore sub-base
Spread and compact the MOT Type 1 hardcore in two separate 50mm layers using a heavy plate compactor to achieve a solid 100mm sub-base.
- Spread and compact the first 50mm layer of MOT Type 1. Spread a 50mm layer of MOT Type 1 hardcore evenly across the excavated patio sub-grade and compact it thoroughly using a heavy plate compactor.
- Tip: Never lay more than 75mm of hardcore in a single pass; for a 100mm sub-base, compact two separate 50mm layers so the bottom 25mm compacts properly.
- Common mistake: Dumping the full 100mm depth of hardcore in one go, which leaves the bottom 25mm uncompacted and prone to sinking later.
- Spread and compact the second 50mm layer of MOT Type 1. Add the second 50mm layer of MOT Type 1 hardcore to bring the sub-base up to the full 100mm depth, then run the plate compactor across the entire surface until solid and level.
- Tip: Use sharp sand with cement for the bedding mortar mix rather than soft sand.
- Tip: Spread and compact stone dust over the Type 1 sub-base to fine-tune the levels before laying tiles.
Step 3: Cut border tiles and stage materials on the blinded base
Cut the 600mm x 600mm ivory porcelain tiles into 200mm x 600mm border strips, blind and compact the sub-base with stone dust, and stage the three sizes of grey tiles alongside the paving primer.
- Cut 600x600mm ivory tiles into 200x600mm border strips. Cut the 600mm x 600mm ivory porcelain slabs down into 200mm x 600mm rectangular strips to form the contrasting picture-frame border around the inside house wall and outer patio perimeter over the stone-dust blinded base.
- Tip: Cut 600mm x 600mm contrasting porcelain tiles into 200mm-wide strips in advance to create a picture-frame border around the patio edges.
- Stage the multi-size grey tiles and prepare the paving primer. Unpack and stack the three sizes of grey porcelain tiles (800x800mm, 800x400mm, and 400x400mm) on the blinded sub-base, plan 'dead man' corner reference tiles for the string line, and set out the tub of paving primer to coat the back of each slab.
- Tip: Set a 'dead man' reference slab in each corner and run a string line between them to guide the border tiles.
- Tip: Paint paving primer onto the underside of every porcelain slab immediately before laying so it bonds firmly to the mortar bed.
- Common mistake: Laying porcelain slabs directly onto a sand-and-cement bed without painting slurry primer on the back.
Step 4: Lay primed porcelain tiles on a semi-dry mortar bed
Trowel out an approximately 1-inch bed of semi-dry sharp sand and cement mortar using a spirit level as a depth gauge, set the pre-primed porcelain tile with four spacers, tap it flush and sloped away from the house with a rubber mallet, and haunch the mortar edges.
- Test the semi-dry mortar consistency and spread the bed. Squeeze a handful of the sharp sand and cement mortar to verify it holds its shape without crumbling or oozing water, then shovel two scoops onto the sub-base and spread it out with a brick trowel across the 400mm x 400mm tile footprint.
- Tip: Mix the bedding mortar to a semi-dry consistency that crushes in your hand and holds its shape without being too wet or too dry.
- Common mistake: Handling raw cement mortar with bare hands, which can cause skin irritation or alkali burns.
- Gauge the mortar bed height using a spirit level. Lay a long spirit level across the adjacent already-laid tiles so it bridges over the new mortar bed, then trowel the mortar until there is a uniform ~20mm (just under 1 inch) gap beneath the level to match the tile thickness.
- Tip: Bridge your spirit level across the adjacent laid slabs over the fresh mortar bed to visually gauge the gap needed for the tile thickness.
- Set the pre-primed tile, insert spacers, and tap flush. Place the pre-primed 400mm x 400mm porcelain tile onto the mortar bed, tap it roughly to height with a white rubber mallet, insert four plastic spacers along the two adjoining edges, and tap the outer corner toward the existing tiles to lock the joints tight.
- Tip: Place four spacers around the adjoining edges and tap into the outer corner of the tile with a rubber mallet to drive it tight against both neighbouring slabs.
- Verify the drainage fall and haunch the mortar edges. Check across the tile joints with the spirit level to ensure zero lippage and confirm a ~1cm fall away from the house across the span, then use the brick trowel to push and pack exposed mortar tightly underneath the open edges of the slab.
- Tip: Always push and pack excess mortar underneath the exposed edges of each finished slab with a trowel to lock the edge in tight.
Step 5: Install recessed drain covers and cut surrounding tiles
Cut off the old circular cast-iron manhole rim with an angle grinder, set the recessed square inspection trays flush with the patio plane, and cut the surrounding porcelain slabs with a wet rail saw to fit neatly around both frames.
- Stage the recessed drain trays and cutting tools. Position the two recessed square manhole covers—one with a circular base for the main inspection chamber and a smaller square unit for the corner drain—and set up the angle grinder and wet tile rail saw.
- Tip: Use a square recessed manhole frame with a circular bottom spigot to convert an old round inspection cover into a tile-in square tray.
- Cut out the old manhole rim and set the new recessed frame. Cut away the old circular cast-iron manhole rim using the angle grinder to lower the chamber height, then bed the new square recessed tray in place flush with the surrounding patio level and slope.
- Cut and lay porcelain tiles around both recessed drain frames. Measure and cut the porcelain slabs using the wet rail saw, then bed them on mortar around the perimeter of both the main inspection chamber frame and the smaller corner drain frame, leaving the internal tray inlays until the surrounding slabs have cured overnight.
- Tip: Wait until the newly laid slabs around the outside of a recessed manhole frame have cured before kneeling on them to cut and fit the internal tray tiles.
- Common mistake: Overshooting internal L-cuts with a circular saw blade at the corners of the square manhole frame.
Step 6: Mix the exterior jointing grout slurry
Pour a tub of exterior jointing grout powder into a flexible mixing bucket containing 4.25 liters of water and blend it thoroughly with a twin-paddle electric mixer until it forms a smooth, pourable slurry.
- Pour the jointing grout powder into 4.25L of water. Measure 4.25 liters of clean water into a flexible mixing tub, then slowly pour in the full bag/tub of dry exterior jointing grout powder.
- Tip: Use 4.25 liters of water per tub of exterior jointing grout (note the on-screen text correction for the spoken '425 mils').
- Common mistake: Pouring fine cementitious grout powder without wearing a dust mask, or splashing grout onto already-laid dry slabs.
- Blend the grout with a twin-paddle mixer and stage the squeegee. Mix the grout powder and water thoroughly using a corded twin-paddle electric mixer for over a minute until a smooth, lump-free, pourable slurry forms, then retrieve the long-handled rubber floor squeegee.
Step 7: Pre-wet the patio and squeegee grout into the joints
Mist the porcelain tiles thoroughly with a pressure washer, pour ribbons of grout slurry across the surface, and work the slurry into all joints with a long-handled rubber squeegee while misting and sweeping off excess material.
- Pre-wet the porcelain tiles with a pressure washer. Fan water across the entire section of porcelain tiles using a pressure washer to thoroughly wet the surface before applying any grout.
- Tip: Always spray water over the porcelain tiles before pouring out the grout slurry so the grout flows easily and does not stick to dry slabs.
- Pour ribbons of grout slurry and squeegee into the joints. Pinch the flexible mixing tub into a spout and pour ribbons of grout slurry across the wet tiles, then use the long-handled rubber squeegee to push the slurry back and forth across the joints until every gap is completely filled. Block open perimeter joint ends with timber or mortar so the liquid grout cannot run out.
- Tip: Block the open outer ends of perimeter joints with a board or mortar dam so the liquid grout slurry does not seep out of the joints.
- Common mistake: Forgetting to dam the open outer edges of border joints, allowing the liquid grout to run out and leave hollow joints.
- Mist the surface and squeegee off excess grout before it sets. Fan a light mist of water over the grouted area with the pressure washer and continuously sweep the rubber squeegee diagonally across the tiles to remove as much excess grout slurry from the slab faces as possible before the 20-to-30-minute setting window expires.
- Tip: Clear hoses and equipment off the patio before grouting so you don't have to lift wet hoses over fresh grout.
- Tip: Keep working the squeegee continuously and misting with water to remove excess grout before it sets rock-hard within 20 to 30 minutes.
- Watch out: Do not let exterior jointing grout cure on the face of the tiles; it sets rock-solid within 30 minutes (to ~53 Newtons) and will permanently ruin the patio finish if not squeegeed and washed off in time.
- Common mistake: Leaving excess exterior jointing grout on the porcelain tiles for too long, ruining the slabs when it cures hard.
Step 8: Wash off remaining grout residue with a pressure washer
Rinse the tile faces and border with a fan spray from the pressure washer once the joints have firmed up to remove any remaining grout film.
- Pressure-wash the grey field tiles toward the outer edge. Wait a few minutes for the grout in the joints to firm up, then sweep the pressure washer fan spray across the grey porcelain field tiles from the house wall toward the outer perimeter to rinse off the remaining slurry film.
- Tip: Let the grout firm up in the joints for a few minutes before doing the final pressure-washer rinse across the tile faces.
- Rinse the ivory border tiles clean. Work the pressure washer spray along the 200mm ivory border tiles to wash all grey grout residue off the light-colored perimeter and off the edge of the patio.