Brick Dome Pizza Oven and Outdoor BBQ Kitchen
Step-by-step guide made from Tidybricks patio restore's YouTube video.
Build a masonry outdoor kitchen featuring a wood-fired brick dome pizza oven, a central concrete prep counter, and a corbeled fire-brick barbecue with a chimney pot. The structure is built on a reinforced concrete block base with arched wood storage bays, a herringbone fire-brick oven floor, and a ceramic-insulated heatproof screed dome.
The full step-by-step Spetz Specs for this project (every part, size, diagram and step, free): Brick Dome Pizza Oven and Outdoor BBQ Kitchen Spetz Specs.
- Difficulty: advanced
Safety
- Always wear a respirator mask, safety glasses, and hearing protection when dry-cutting concrete blocks with a 9-inch angle grinder.
- Wear a respirator and gloves when cutting and handling ceramic fiber blanket, as airborne refractory ceramic fibers are hazardous to inhale.
- Ensure the cutting disc on an angle grinder is mounted in the correct rotation direction and keep sparks directed away from bare skin.
Must know before you build
- Extend base insulation board under outer dome walls to stop heat bridging into the concrete slab.
- Soak fire bricks in water before laying to prevent them pulling moisture from refractory cement.
- Mount a swivel caster to a wooden cross base to create a smooth 360-degree dome trammel pivot.
- Support top crown bricks using a wet sand mound packed over thermal blocks inside the dome.
- Light a low curing fire to dry refractory mortar before wrapping insulation blanket and screed.
Tools
- Wheelbarrow (builder's wheelbarrow)
- Bricklayer's trowel (pointing and masonry trowels)
- Spirit level (box-beam spirit levels)
- Tape measure (retractable pocket tape measure)
- String line (bricklayer's line and pins)
- Club hammer (lump hammer)
- Framing square (metal L-square)
- Angle grinder (corded 9-inch angle grinder, Makita, 9 in diamond blade)
- Hand saw (wood crosscut hand saw)
- Cordless impact driver (Makita, 18V)
- Wet brick saw (benchtop masonry table saw)
- Soft brush (handheld masonry brush / broom head) (optional)
- Shovel (square-mouth builder's shovel)
- Rotary hammer drill (corded SDS rotary hammer drill) (optional)
- Rubber mallet (optional)
- Sponge (masonry cellulose sponge) (optional)
- End nippers (pincer wire cutters)
- Diagonal pliers (side-cutting pliers)
Materials
- Concrete (site-mixed concrete, 6 in thick footing, 4 in thick countertop slabs)
- Steel rebar mesh (welded steel reinforcement mesh)
- Concrete blocks (solid dense concrete blocks, 9 in and 4 in)
- Mortar (sand and cement masonry mortar)
- Concrete lintels (6, precast reinforced concrete lintels)
- Stainless steel BBQ grill insert (1, drop-in charcoal BBQ grill grate with ash pan drawer)
- Plywood (structural plywood sheet)
- Timber (treated softwood framing lumber)
- Wood screws (countersunk screws)
- Rustic red bricks (reclaimed-style facing bricks)
- Outdoor oven cement (refractory fire cement, VITCAS, VITCAS OC, 20kg tubs)
- Fire bricks (refractory fire bricks, VITCAS)
- Ceramic fiber insulation board (rigid high-temperature insulation board)
- Swivel caster wheel (1, plate-mount swivel caster)
- Pizza oven door (1, arched metal oven door with thermometer and viewing window)
- Stainless steel chimney flue (1, flue pipe with rain cap and base plate)
- Clay chimney pot (1, flared terracotta/clay chimney pot)
- Thermal blocks (lightweight aerated concrete blocks)
- Building sand (wet building sand)
- Ceramic fiber blanket (1 roll, high-temperature refractory insulation blanket, 2300 mm cut length)
- Chicken wire mesh (2 rolls, galvanized hexagonal wire netting)
- Tie wire (galvanized binding wire)
- Heatproof screed (5 tubs, ready-mixed refractory screed, VITCAS, VITCAS HPS, 20kg tubs, rated to 1400°C / 2550°F)
Step by step
Step 1: Lay the First Concrete Block Courses
Lay the first courses of 9-inch concrete blocks flat in mortar along the perimeter footing using a string line and spirit level.
- Set the Rear Line and Lay the First Flat Block Course. Stretch a string line along the rear edge of the concrete footing, spread a bed of mortar, and lay the first course of dense concrete blocks flat on their 9-inch side.
- Tip: Lay the 9-inch concrete blocks flat for the main structural walls to provide a wide bearing surface for the concrete slab.
- Build Up the Left Side Wall Courses. Lay three staggered courses of flat concrete blocks along the left-hand pizza oven wall, checking each course for plumb and level with a spirit level and framing square.
Step 2: Build the Base Walls and BBQ Pillars
Mortar the concrete block courses for the rear wall, prep bay, and BBQ side pillars, checking corners for square and level.
- Lay the Rear Wall and Right-Hand BBQ Pier. Mortar staggered courses of concrete blocks along the rear retaining wall and build up the right-hand return pier for the barbecue bay, checking plumb and level after each course.
- Build the Central Dividing Walls. Lay the internal block dividing wall between the pizza oven bay and the central prep area, and add additional courses to the rear wall.
- Square and Build the Left BBQ Pier. Check the inner BBQ corner with a framing square and lay the concrete block courses for the left-hand BBQ pier, stepping the front blocks to match the right pier.
- Tip: Check the BBQ pier corners with a framing square so the stainless steel grill insert slides in squarely.
Step 3: Build the Pizza Oven Base Walls
Lay concrete blocks over the precast lintel base to form the lower storage enclosure under the pizza oven.
- Mortar Concrete Blocks Around the Lintel Perimeter. Place a temporary board over the concrete lintels to stand on, then mortar courses of concrete blocks along the left, rear, and right walls of the pizza oven base.
Step 4: Trim the Rear Wall and Build Arch Templates
Cut the rear block wall down to height with an angle grinder, screw together curved plywood and timber arch templates, and build up the surrounding block walls.
- Cut Down the Rear Prep Bay Wall with an Angle Grinder. Score along the pencil line on the top course of the rear prep bay wall using a 9-inch angle grinder, knock off the top section of blockwork, and brush away the dust.
- Watch out: Wear a respirator and eye protection when cutting concrete blocks with an angle grinder, as it generates heavy clouds of masonry dust.
- Cut and Screw Together the Wooden Arch Template. Cut timber spacer blocks with a hand saw and screw curved plywood side panels to the timber spacers using a cordless impact driver to form an arch centring template.
- Test-Fit the Arch Templates and Raise the Rear Block Wall. Lay the front pier blocks for the pizza oven bay, test-fit the wooden arch templates in the openings, and lay 4-inch concrete blocks on edge to raise the rear backing wall behind the prep and BBQ bays.
Step 5: Lay the Brick Storage Arches
Mortar the rustic red bricks across the wooden arch templates on both the prep bay and the pizza oven base.
- Mortar the Prep Bay Brick Arch. Mark the brick positions on the wooden arch template, stretch a string line across the front face, and mortar the rustic red bricks across the prep bay arch.
- Tip: Mark the dry-fitted brick positions on the wooden arch template with a pencil and run a string line across the front to keep the arch even.
- Mortar the Pizza Oven Bay Brick Arch. Set the second wooden arch template over the pizza oven base opening, lay rustic red bricks in mortar from both ends toward the center, and pack the wedge-shaped mortar joints full.
Step 6: Pour the Prep Countertop Concrete Slab
Place the plywood shuttering and steel rebar mesh over the prep bay, wet the masonry edges, and shovel and trowel the 4-inch concrete slab level.
- Position the Plywood Shuttering and Rebar Mesh. Set the plywood shuttering sheet onto the internal supports inside the prep bay and lay the cut grid of steel rebar mesh on top so it sits mid-depth in the 4-inch slab cavity.
- Wet the Formwork and Surrounding Block Edges. Brush water generously over the plywood shuttering and the surrounding concrete block and brick arch edges using a soft masonry brush.
- Tip: Wet down the shuttering and surrounding masonry edges before pouring concrete in warm weather so the slab doesn't dry too quickly.
- Shovel and Trowel the Prep Counter Concrete. Shovel wet concrete into the 4-inch prep counter form, work it through the steel rebar mesh with a trowel to eliminate voids, and level it flush with the top of the surrounding blockwork.
Step 7: Cut Steel Rebar Mesh for the Oven Slab
Cut the steel reinforcement mesh to size for the pizza oven slab using an angle grinder.
- Cut the Steel Mesh Grid Over a Wheelbarrow. support the sheet of steel rebar mesh across a wheelbarrow and slice through the crossbars with an angle grinder to size the mesh for the pizza oven base.
- Watch out: Wear long trousers and eye protection when cutting steel rebar with an angle grinder to prevent burns from hot sparks.
- Common mistake: Mounting or holding the angle grinder so the cutting disc throws hot metal sparks directly onto your bare legs.
Step 8: Pour and Vibrate the Pizza Oven Concrete Slab
Set double layers of steel rebar mesh over the plywood form, wet the masonry, pour and screed the concrete slab, and vibrate it with a hammer drill.
- Lay Double Rebar Mesh on Masonry Spacers and Wet the Form. Prop the first layer of steel rebar mesh on small masonry offcuts over the plywood form, lay a second spare sheet of rebar mesh on top, and brush water over the plywood and surrounding block edges.
- Tip: Use small masonry offcuts as spacers under the steel rebar mesh so it sits suspended inside the concrete slab rather than flat against the bottom board.
- Pour and Screed the Pizza Oven Concrete Slab. Shovel wet concrete into the pizza oven slab form, spread and compact it around the double rebar mesh with a trowel, and screed the surface flat across the perimeter block walls using a long spirit level.
- Vibrate the Slab with a Hammer Drill and Re-Screed. Press a rotary hammer drill against the outer concrete block perimeter walls to vibrate air bubbles out of the slab, then top up low spots with fresh concrete and screed the surface smooth again with the spirit level.
- Tip: Press a rotary hammer drill against the outer block walls to vibrate air pockets out of the wet concrete slab, then top up and re-screed any low spots that settle.
Step 9: Lay Fire Bricks for the BBQ Firebox
Lay courses of soaked fire bricks with outdoor oven cement around the interior walls of the BBQ bay.
- Lay Staggered Courses of Fire Bricks in the BBQ Bay. Butter soaked fire bricks with Vitcas outdoor oven cement and lay staggered courses along the left, rear, and right walls of the BBQ firebox, tapping each brick plumb and level.
- Tip: Soak fire bricks in a wheelbarrow of water before laying them so they don't draw moisture out of the outdoor oven cement too quickly.
Step 10: Dry-Lay the Herringbone Fire Brick Floor
Arrange whole fire bricks in a tight herringbone pattern over the ceramic fiber insulation board.
- Dry-Fit Fire Bricks in a Herringbone Pattern. Place whole fire bricks tightly together in a 45-degree herringbone pattern centered over the ceramic fiber insulation board until the entire oven floor area is covered.
Step 11: Mark and Cut the Circular Oven Floor
Mark the front tunnel edge and center point on the herringbone bricks, scribe the dome circle using a string compass, and cut the bricks and insulation board to shape.
- Swap Lipped Bricks and Mark the Front Tunnel Edge. Check the herringbone floor by hand and swap or flip any bricks with raised lips, then position two front tunnel bricks and mark the straight front threshold line with a spirit level and pencil, leaving a pencil-width gap at the front for render bead.
- Tip: Run your hand over the dry-laid herringbone bricks and flip or swap any bricks that have a raised lip so the cooking floor is completely flat.
- Tip: Set the front tunnel bricks back by the width of a pencil from the front concrete edge to leave room for the render bead to cover the insulation board.
- Mark the Centerline and Pivot Point. Use a spirit level aligned with the center herringbone joints to draw the front-to-back centerline across the bricks, then measure back from the tunnel line and drive a screw into the center brick joint.
- Scribe the Dome Circle with a String Compass. Tie a string to the center screw, wrap the other end around a pencil at the desired radius, and swing the taut string around the herringbone bricks to draw the circular perimeter of the oven floor.
- Tip: Drive a screw into the center joint of the herringbone floor and use a piece of string tied to a pencil as a compass to scribe the circular floor cut line.
Step 12: Lay the Soldier Course and Cut Half Bricks
Mortar the vertical soldier course of fire bricks around the circular oven floor perimeter and cut fire bricks in half on a wet masonry saw.
- Mortar the Vertical Soldier Course Around the Floor. Dip each fire brick in a bucket of water, apply Vitcas outdoor oven cement, and stand the bricks upright around the cut perimeter of the circular herringbone floor, using the notched trammel arm to set the height and radius.
- Tip: Dip each fire brick in a bucket of water right before buttering it with oven cement so the dry brick doesn't suck the moisture out of the mortar.
- Common mistake: Placing the soldier course directly on the concrete slab outside the ceramic insulation board, which creates a thermal bridge that conducts heat into the concrete.
- Cut Fire Bricks in Half on the Wet Masonry Saw. Set whole fire bricks on the sliding table of the wet masonry saw and cut them in half crosswise to prepare half-bricks for the curved dome courses.
Step 13: Build the Pizza Oven Entry Arch
Mortar the fire bricks around the oven door frame and construct the arched lintel over the doorway.
- Mortar the Side Pillars Around the Oven Door. Prop the metal pizza oven door in position at the front threshold and mortar courses of fire bricks up both sides of the door frame, checking plumb and level with a spirit level.
- Dry-Fit and Mark the Entry Arch Bricks. Set angled skewback bricks on the side pillars and dry-fit the arch bricks across the curved top of the oven door frame, marking the cut lines with a pencil.
Step 14: Lay the Lower Courses of the Brick Dome
Lay staggered courses of half fire bricks around the dome using outdoor oven cement and the rotating wooden trammel arm to set the inward angle.
- Lay the First Angled Course of Half Bricks. Start at the rear center of the soldier course, apply Vitcas outdoor oven cement, and lay half fire bricks in both directions around the circle, resting the inner bottom edge of each brick against the notched wooden trammel arm.
- Tip: Start each course of dome bricks at the rear wall directly opposite the oven door and work outward in both directions so the most visible joints stay neatly staggered.
- Lay the Second and Third Staggered Dome Courses. Dip each half fire brick in water, butter the bottom and side faces with oven cement, and lay the second and third staggered courses around the dome using the rotating trammel arm to set the inward slope.
Step 15: Mortar the Chimney Flue Base
Position the stainless steel chimney flue pipe on the entry arch and mortar fire bricks around its base.
- Set the Chimney Flue and Mortar the Front Arch. Set the stainless steel chimney flue pipe over the vent opening in the front entry arch and mortar the outer arch fire bricks around the flue base.
- Tip: Leave the protective plastic wrap on the stainless steel chimney flue while laying bricks and screeding around it to keep mortar off the metal.
Step 16: Build the Middle Courses of the Brick Dome
Lay successive courses of half fire bricks up the dome with the trammel arm and tie the brickwork around the chimney flue collar.
- Lay the Fourth and Fifth Dome Courses and Tie Into the Arch. Lay the fourth and fifth courses of half fire bricks around the dome using the trammel arm, and mortar angled fire bricks where the dome courses meet the front entry arch and chimney flue base.
- Lay the Upper-Middle Dome Courses. Continue laying staggered courses of half fire bricks around the upper-middle section of the dome with the trammel arm until the inward angle becomes too steep for the bricks to stay in place without sliding.
Step 17: Lay the Corbeled BBQ Hood Courses
Mortar courses of fire bricks on the BBQ walls, stepping each upper course inward to form the angled chimney hood.
- Lay the Upper BBQ Firebox Walls and Shelf Ledges. Mortar courses of fire bricks along the left, rear, and right walls of the BBQ firebox, setting two courses slightly proud on the inner side walls to act as shelf supports.
- Tip: Offset a course of fire bricks slightly inward on both side walls of the BBQ firebox to create built-in ledges for holding grill grates or warming shelves.
- Begin Corbeling the BBQ Hood Inward. Lay the first inward-stepping corbel courses of fire bricks on the left and right BBQ walls, checking each course for level and plumb with a spirit level.
Step 18: Continue Corbeling the BBQ Hood
Lay additional inward-stepping courses of fire bricks to narrow the top of the BBQ hood.
- Lay Upper Corbel Courses on the BBQ Hood. Mortar three more inward-stepping courses of fire bricks onto the left, right, and rear walls of the BBQ hood, checking level and plumb on each step.
- Tip: Stop laying corbeled courses and let the mortar cure if the overhanging bricks start to feel unstable, and backfill behind them with concrete to counterbalance the overhang.
Step 19: Cap the BBQ Hood and Install the Chimney Pot
Cut and mortar the final top course of fire bricks on the BBQ hood and bed the clay chimney pot in oven cement.
- Cut and Mortar the Top Corbel Course. Measure the top opening of the BBQ hood, cut fire bricks on the wet masonry saw, and mortar the final corbeled ring around the top of the hood, wiping the joints clean with a wet sponge.
- Bed the Clay Chimney Pot on the BBQ Hood. Spread a thick bed of Vitcas outdoor oven cement around the top brick opening of the BBQ hood and set the clay chimney pot firmly in place.
Step 20: Sculpt the Sand Form and Close the Dome Crown
Mound wet building sand over the blocks to form the crown curve, lay mitered fire bricks around the top, and pack triangular brick wedges and oven cement into the center gap.
- Sculpt the Wet Sand Mound and Lay Two Mitered Courses. Pack and smooth wet building sand over the plastic-covered thermal blocks to match the dome curvature, then lay two courses of wedge-mitered half fire bricks in oven cement around the sand mound.
- Tip: Stack halved thermal blocks inside the oven, cover them with plastic bags, and sculpt a mound of wet sand on top to support the final crown bricks.
- Pack the Center Crown with Brick Wedges and Oven Cement. Set four upright fire bricks and four triangular brick wedges into the central crown opening, pack Vitcas outdoor oven cement deep into the joints using a pencil, and cap the center gap flush with cement.
- Tip: Use a pencil to poke and pack outdoor oven cement all the way down into the narrow gaps between the final crown bricks.
Step 21: Remove the Support Blocks and Sand from the Oven
Open the pizza oven door and pull out all the internal thermal blocks, plastic bags, and building sand.
- Pull Out the Lower Thermal Blocks. Open the pizza oven door and reach inside to pull out the first layer of halved thermal blocks supporting the sand mound.
- Clear Out the Remaining Blocks, Plastic Bags, and Sand. Remove the remaining thermal blocks and plastic bags through the oven doorway and scoop and brush all the loose building sand out of the herringbone floor.
Step 22: Lay the Front Brick Arch on the BBQ
Mortar rustic red bricks over the wooden arch template across the front opening of the BBQ hood.
- Mortar Rustic Bricks Across the BBQ Arch Template. Butter rustic red bricks with Vitcas outdoor oven cement and lay them across the wooden arch template on the front of the BBQ hood, aligning the front faces to a taut string line.
- Tip: Set the decorative brick arch slightly proud of the surrounding block and brick walls if you plan to render the exterior, so the finished render sits flush with the arch.
Step 23: Wrap the Dome in Ceramic Blanket and Wire Mesh
Drape cut lengths of ceramic fiber blanket over the brick dome, tuck the edges with a trowel handle, stitch the seams with tie wire, and wrap chicken wire mesh tightly over the insulation.
- Measure and Roll Out the Ceramic Fiber Blanket. Measure the over-the-top diameter of the brick dome (2300 mm), roll out the ceramic fiber insulation blanket on the patio, and measure out the cut length.
- Watch out: Wear a respirator mask and gloves when unrolling, cutting, and handling ceramic fiber blanket.
- Tuck the Blanket Into Corners and Stitch Seams with Tie Wire. Drape the ceramic fiber blanket strips over the dome and around the chimney flue, press the blanket tightly into the front tunnel corners using a trowel handle, trim off excess overhang, and twist tie wire across the seams with end nippers.
- Tip: Use the rounded handle of a trowel to press the ceramic fiber blanket tightly into the corners around the front entry arch before trimming it.
- Tip: Stitch adjacent strips of ceramic fiber blanket together with short pieces of tie wire so the insulation doesn't slip off the dome while you fit the mesh.
- Wrap and Stitch Chicken Wire Mesh Over the Blanket. Cut strips of galvanized chicken wire mesh, drape them over the ceramic fiber blanket, and twist tie wire through the overlapping mesh panels to pull the wire snug against the dome.
Step 24: Apply Heatproof Screed Over the Dome
Trowel the heatproof screed over the chicken wire mesh to completely encase the insulated pizza oven dome.
- Trowel Heatproof Screed Around the Lower Dome. Scoop mixed Vitcas heatproof screed onto a bricklayer's trowel and press it firmly into the chicken wire mesh around the lower sides and front arch of the dome.
- Screed the Top Crown of the Dome Smooth. Apply the remaining tubs of heatproof screed over the top crown of the dome and around the chimney flue collar, smoothing the entire hemisphere with the flat of the trowel.